Analog Speakers
CC2X2LI7S - 2x2 Ceiling Tile Speaker (70v)
The 2x2 speaker allows for a quick installation with just the need to replace a standard 2x2 ceiling tile. The 2x2 speaker also has four (4) seismic tie-off points to comply with local codes in most jurisdictions! It comes fully assembled and can be installed in a ceiling grid in about a minute, which saves installation labor!
The 2x2 Speaker features:
- The CC2X2LI7S provides high intelligibility, visual appeal and excellent reliability; making it ideal for a wide range of commercial sound applications
- The enclosure has a high durability, powder coated and perforated baffle
- The speaker inside is a lightweight speaker assembly that includes an 8", high efficiency speaker with a 5oz magnet and 4Watt, 25/70V transformer
These speakers are used in locations that have ceiling tile grid unless otherwise noted.
CC2PKCI7LS - Cut-In Speaker (70v)
The cut-in speaker is a complete speaker/transformer/baffle/backbox/tile bridge assembly. These cut-in speakers are designed for drop-ceiling tile installations.
The Cut-In Speaker features two of each of the following:
- The CC2PKCI7LS a 8" O.D. speaker with a 10oz magnet and a 5Watt, 25/70V transformer
- Round, steel, stud-mount baffle
- Rust-resistant steel, load bearing support bridge
- Round, steel, 275 CID backbox
These speakers include two (2) complete speaker assemblies!
CC7WMSQS - Wall Mounted Speaker (70v)
The wall mounted speaker is perfect for indoor use, where a ceiling speaker may not be applicable. These wall mounted speakers are can be mounted in areas that may need more robust speaker unit.
The Square Wall Mounted Speaker features:
- A complete loudspeaker system consisting of an 8" O.D. dual cone loudspeaker with a 5oz magnet and a 5Watt, 25/70V transformer
- The enclosure is a square (screw mounted), steel baffle with a square, steel, vandal resistant, surface mounted enclosure
- Has four (4) 8-32 threaded inserts, a single 1/2" conduit entrance on the back and two (2) Wiremold knockouts
- White powder coated finish
These speakers are great in areas like the kitchen, boiler room or any other locations that may require a more rigid audio device!
CC7WMSLB - Wall Mounted Speaker Slanted (70v)
The wall mounted speaker is perfect for indoor use, where a ceiling speaker may not be applicable. These wall mounted speakers are can be mounted in areas that may need more robust speaker unit with a slanted direction pointing downward.
The Slanted Wall Mounted Speaker features:
- A complete loudspeaker system consisting of an 8" O.D. dual cone loudspeaker with a 5oz magnet and a 5Watt, 25/70V transformer
- The enclosure is a square (screw mounted), steel baffle with a slanted, steel, vandal resistant, surface mounted enclosure
- Has four (4) 8-32 threaded inserts, a single 1/2" conduit entrance on the back and two (2) Wiremold knockouts
- White powder coated finish
These speakers are great in areas like the kitchen, boiler room or any other locations that may require a more rigid audio device!
CCSPKAPH15 - Paging Horn (70v)
The analog paging horn provides intelligible voice paging and tone signaling which makes it great for outdoor and indoor sound system applications!
The Analog Paging Horn features:
- 15Watt, 8Ω
- Fully weather proof horn for reliable operation in demanding environments; IP67 Rating
- Easy to install on a wall, pole or ceiling; the mount applications include corrosion resistant stainless steel mounting hardware
- The loud-speaker diaphragm is heat and moisture-resistant to prevent deformation and extend operation
These horns are typically in areas around the exterior perimeter of the building (around exits and pointing in directions of landmarks; i.e. playgrounds, parking lots, etc.). They can also be placed on the inside of buildings where a horn speaker may be needed; such as a gym or a warehouse!
CLCIS87 - 8Ohm/70Volt Cut-In Speaker (8Ω/70v)
This cut-in speaker has a 6" woofer and a 1" treble speaker. It has a turn dial to choose between 8Ω or 70V and it perfect for areas that need a cut-in speaker! If your school has a hard-lid ceiling and do not want to install wall mounted speakers; you can cut a hole in the ceiling and install these speaker units, making it a nice and sleek install!
The Cut-In Speaker features:
- A high performance, 2-way speaker
- Has a heavy duty, fire dome and power selection switch
- Great for high music demand applications
CL2X2LI8B - 8Ohm 2x2 Ceiling Tile Speaker (8Ω)
The 2x2 speaker allows for a quick installation with just the need to replace a standard 2x2 ceiling tile. The 2x2 speaker also has four (4) seismic tie-off points to comply with local codes in most jurisdictions! It comes fully assembled and can be installed in a ceiling grid in about a minute, which saves installation labor!
The 2x2 Speaker features:
- 20Watt, 8Ω
- The CL2X2LI8B provides flat frequency response and excellent sound in a 2x2 lay-in ceiling tile replacement enclosure; making it ideal for a wide range of demanding applications
- The enclosure has a high durability, powder coated and perforated baffle
- The speaker inside is a lightweight speaker assembly that includes an 8" 8Ohm speaker with a 10oz magnet and a foam edge
These speakers are used in locations that have ceiling tile grid unless otherwise noted.
CL65WM - 8Ohm Wall Mounted Speaker (8Ω)
This wall mounted speaker is perfect for areas where drop-ceiling may not be available! Comes with a 360° rotatable bracket for horizontal and vertical installation angle adjustment; allowing for a delightful installation experience.
The Wall Mounted Speaker features:
- 60Watt, 8Ω
- Fully weatherproof loudspeakers; IP66 weatherproof finish for all extreme weather applications
- Stylish design; ABS Enclosure, stainless metal grille and stainless mounting bracket
- Great sound; 70v/100v speaker with power tapping or as a low impedance 8Ohm speaker
These speakers consist of a 6.5" weatherproof woofer and a 1" silk tweeter!
